 |
05-03-2012, 07:43 PM
|
|
Junior Member
|
|
Join Date: Feb 2011
Posts: 23
|
|
huebsch jt0300drg has sparking but no lighting up the flame?
hi all expert.
i have a huebsch dryer it has sparking light but no light up the flames.
i have changed the relay, ignition box, thermistor. and i had washed the burner tube with water then blowed by air press. when i put the tube back on it working very hot at the first. after that it no light up again. meanwhile, before i washed the tube it was working fine but not very hotter.
any suggestion is appreciate...
|
05-04-2012, 09:06 AM
|
|
Junior Member
|
|
Join Date: Apr 2012
Posts: 10
|
|
I had a similar problem with a dexter dryer, and I solved it by changing the igniter probe. Also, make sure you're getting a good flow of gas. I have seen valves go bad on old machines.
|
05-05-2012, 07:21 PM
|
 |
Senior Member
|
|
Join Date: Jun 2004
Location: So California
Posts: 1,257
|
|
Change out both gas valve coils. Sometimes only swapping out one will do the trick.
__________________
Kenny
Got Dirty Laundry? Come Clean With Us.
|
05-14-2012, 12:25 PM
|
|
Junior Member
|
|
Join Date: Feb 2011
Posts: 23
|
|
thank you for all the information gave. i just had find out this sometime can light up with very weak flame then goes a little bit more flame. sometime it can light up very very weak flame at a few second then dead.
question..
1. is the gas pressure has the problem.. because this dryer is locate at the up last machine for the gas pipe line?
2. is the gas valve has problem?
what can i do...
|
05-15-2012, 07:00 AM
|
 |
Senior Member
|
|
Join Date: Feb 2007
Location: Muskegon, Michigan
Posts: 6,756
|
|
Flowerhorn,
It could be either. You can ask the gas company to check the pressure at that dryer or you can switch the gas valve with another dryer (on the other end of the row) and see if the problem switches to the other dryer or not.
__________________
"Lead, follow or get out of the way." Larry Adamski
|
05-15-2012, 10:41 AM
|
 |
Senior Member
|
|
Join Date: Oct 2007
Location: FLORIDA 2-Mat's
Posts: 1,136
|
|
Quote:
Originally Posted by flowerhorn
hi all expert.
i have a huebsch dryer it has sparking light but no light up the flames.
i have changed the relay, ignition box, thermistor. and i had washed the burner tube with water then blowed by air press. when i put the tube back on it working very hot at the first. after that it no light up again. meanwhile, before i washed the tube it was working fine but not very hotter.
any suggestion is appreciate...
|
Sounds like the machine is Not Sensing the Flame, if the ignition box has been changed, it is most likely the ignitor or the lead.
__________________
If your Vend Prices are Determined Solely by what your Competitors Charge, you are only as Smart as your Dumbest Competitor.
"In Five Years These Be the Good Ole Days"
Want to Invest in America & Save Jobs? "Buy American Products"
Mike,
From Sunny Florida USA
|
05-22-2012, 11:02 AM
|
|
Junior Member
|
|
Join Date: Feb 2011
Posts: 23
|
|
Quote:
Originally Posted by Adamski
Flowerhorn,
It could be either. You can ask the gas company to check the pressure at that dryer or you can switch the gas valve with another dryer (on the other end of the row) and see if the problem switches to the other dryer or not.
|
first, thank you for all you guys informations.
larry, if the gas pressure has problem , then my bottom dryer should be also have the problem. right
|
05-22-2012, 03:16 PM
|
|
Senior Member
|
|
Join Date: Feb 2007
Location: Muskegon, Michigan
Posts: 6,756
|
|
Quote:
Originally Posted by flowerhorn
... larry, if the gas pressure has problem , then my bottom dryer should be also have the problem. right
|
Flower,
If the bottom dryer is plumbed to the same gas distribution pipe as the upper dryer; I would expect a low pressure problem to show symptoms in both dryers.
__________________
"Lead, follow or get out of the way." Larry Adamski
|
06-06-2012, 04:00 PM
|
|
Member
|
|
Join Date: Jun 2010
Location: FL
Posts: 64
|
|
Quote:
Originally Posted by flowerhorn
hi all expert.
i have a huebsch dryer it has sparking light but no light up the flames.
i have changed the relay, ignition box, thermistor. and i had washed the burner tube with water then blowed by air press. when i put the tube back on it working very hot at the first. after that it no light up again. meanwhile, before i washed the tube it was working fine but not very hotter.
any suggestion is appreciate...
|
If it lights but then goes out change the high voltage lead first. Remember on an Alliance made tumbler with spark ignition the lead not only carries the current for the spark but also the signal for proof of flame.
|
|
|
Linear Mode
